銅裝飾品包括銅屋頂、 銅幕墻、 銅門、 銅窗、 銅電梯以及各種銅制的家居品等。浙江銅門廠指出， 銅幕墻更是作為一種裝飾性材料在建筑中使用， 是由結構框架與鑲嵌銅板材 組成， 不承擔主體結構載荷的建筑圍護結構。創意街的三大盒形建筑分別為“飛 來石” 、 “天堂火”和“琉璃水坊” 。

 

Copper decorations include copper roofs, curtain walls, doors, windows, elevators and various copper household products. Zhejiang Tongmen Factory pointed out that the copper curtain wall is used in buildings as a decorative material, which is composed of structural frame and inlaid copper plate, and does not bear the main structural load of the building envelope structure. The three box-shaped buildings of Creative Street are "Flying Stone", "Heaven Fire" and "Liulishuifang".

 

 

 

這些建筑的二樓都是銅幕墻，并隨意穿插了 矩形的玻璃窗，由傾斜的鋼柱支撐，一樓全部安裝了透明的玻璃幕墻。這些現代 雕塑般的建筑，自成一個整體，以原銅色、暗棕色和翠綠色三種銅材料裝飾外墻 的建筑分布在河邊， 與河邊環境和諧配合。而接近于路邊梧桐樹顏色的原棕色銅 板材更是第一次在中國使用。 應用了預處理的銅幕墻系統， 對于維護的要求不高， 同時在陽光、雨水等環境因素和時間都會影響氧化的過程，色彩亦相應變化，正 如當地的梧桐樹在每個季節色彩會有變化。根據估算，在約 10 年后，所有原銅 色、暗棕色銅幕墻將慢慢變成翠綠色，成為真正“有生命的建筑” 。 銅裝飾是一種量身定做的產品。

 

The second floor of these buildings are all copper curtain walls with rectangular glass windows, supported by inclined steel columns, and transparent glass curtain walls are installed on the first floor. These modern sculpture-like buildings, as a whole, decorated with original copper, dark brown and emerald green three kinds of copper materials, distribute along the riverside and coordinate harmoniously with the riverside environment. The original brown copper sheet, which is close to the color of the parasol tree, is used for the first time in China. The application of pretreated copper curtain wall system does not require high maintenance. At the same time, environmental factors such as sunshine, rainwater and time will affect the oxidation process, and the color will change accordingly, just as the local plane tree color will change in each season. It is estimated that in about 10 years, all the original copper and dark brown copper curtain walls will gradually become turquoise green and become truly "living buildings". Copper decoration is a custom-made product.

 

 

 

銅裝飾加工過程中特別應注意以下幾點-銅門廠家來為大家娓娓道來：

 

In the process of copper decoration processing, we should pay special attention to the following points - copper door manufacturers to tell you:

 

 

 

（一）、焊接工藝：

 

(1) Welding technology:

 

 

 

（1） 、 焊接質量的好壞直接影響裝配質量，因此在構件安裝時，要嚴格控 制焊接處的間隙， 錯邊等誤差， 經安裝裝配后的焊接節點須經專人檢查合格后才 能交焊工施焊。

 

(1) Welding quality directly affects the assembly quality. Therefore, in component installation, it is necessary to strictly control the gaps and errors such as staggered edges. After installation and assembly, the welded joints must be inspected and qualified by a specialist before they can be welded by the welder.

 

 

 

（2） 、焊接前的準備工作：

 

(2) Preparations before welding:

 

 

 

a、裝配好的焊接節點專人檢查后 交于焊工施焊；

 

A. The assembled welded joints are inspected by a special person and handed over to the welder for welding.

 

 

 

b、檢查焊接位臵的腳手搭設是否安全可靠；

 

B. Check the safety and reliability of the scaffolding of the welding position.

 

 

 

c、清理焊接坡口 區，將經烘焙的焊條用保溫筒帶至現場焊接地點。

 

C. Clean up the welding groove area and bring the baked electrode to the spot welding site with insulating barrel.

 

 

 

（3） 、焊接工作 a、為避免 焊接變形，焊接時采用對稱焊接（包含對焊、立焊、斜焊） ；b、焊接過程中逐道 焊縫清渣，除飛濺物，發現缺陷及時用角向砂輪打磨，除去缺陷；c、焊接工作 結束，將焊縫區及焊接工作位臵場地清理干凈，轉移到下一焊接節點。

 

(3) Welding work a. In order to avoid welding distortion, symmetrical welding (including butt welding, vertical welding and oblique welding) is used in welding; B. Slag removal of weld seam one by one during welding process, spatter removal, timely grinding with angular grinding wheel to remove defects; C. After welding work, weld zone and welding working site are cleared. Clean up and transfer to the next welded joint.

 

 

 

（4） 、 焊后檢查

 

(4) Post-weld inspection

 

 

 

a、待焊縫冷卻后，進行焊縫外觀檢查；b、焊縫中不得有裂縫，焊縫金 屬與母材間完全熔合，所有破口均被填滿；

 

(a) After the weld is cooled, the appearance of the weld shall be inspected; b) There shall be no cracks in the weld, and the weld metal and base metal shall be completely fused, and all the cracks shall be filled;

 

 

 

（二） 、表面處理工藝

 

(2) Surface treatment technology

 

 

 

1、除油、除銹除氧化皮——水洗——酸洗拋光——水洗——中和——水洗 ——著色處理——水洗——干燥及其它后處理

 

1. Oil removal, rust removal and oxide skin removal - water washing - acid washing polishing - water washing - neutralization - water washing - coloring treatment - water washing - drying and other post-treatment

 

 

 

2、 酸洗拋光推薦使用銅材酸洗拋 光液進行處理。目的是使黃銅表面具有光澤。

 

2. Copper pickling polishing fluid is recommended for acid pickling polishing. The purpose is to make the surface of brass glossy.

 

 

 

3、將工件浸泡于調配的銅發黑劑 中，2 分鐘左右黃銅表面即變成黑青色，根據實驗結果。浸泡時間為 20－25 分鐘 時，表面變色****，可獲得較好的防銹性能。工件可重復浸泡，增加變色層 厚度，可獲得滿意效果。

 

3. Immerse the workpiece in the blended copper blackening agent, and the brass surface will turn black and blue in about 2 minutes. According to the experimental results. When the soaking time is 20-25 minutes, the surface becomes discolored ** and better anti-rust performance can be obtained. The workpiece can be soaked repeatedly to increase the thickness of the chromotropic layer, and satisfactory results can be obtained.

 

 

 

**重要也是用戶**關心的莫過于銅裝飾（銅門十大品牌）的保養， 保養的時候應當注意以 下問題：

 

The maintenance of copper decoration (the top ten brands of copper door) is of great importance to users. The following issues should be paid attention to in maintenance:

 

 

 

1、由于水是銅裝飾的危害者之一，空氣濕度過大，會使其受到腐蝕，因而 就要特別注意要在干燥的環境中存放。

 

1. As water is one of the harmful elements of copper decoration, excessive humidity in the air will cause corrosion, so special attention should be paid to storage in a dry environment.

 

 

 

2、預防受到機械性損壞，相互間不應該彼此碰撞、不要疊壓碼放、對于細 工精制和容易損壞的，更加要小心維護。

 

2. Prevent mechanical damage, do not collide with each other, do not overlap codes, for refined and easily damaged, more careful maintenance.

 

 

 

3、要防御一些外界的有害化學物質，如：酸類、氯化物等，在移動鑄銅裝 飾時一定要戴棉制手套方可移動，以免手上的汗腐蝕。

 

3. To defend against harmful chemicals, such as acids and chlorides, cotton gloves must be worn when moving the decoration of cast copper so as to avoid sweat corrosion on the hands.

 

 

 

4、 進行清潔的時，要用干凈而又柔軟的布片來擦去灰塵，對于有些溝處不 易用布擦到的地方**用毛刷或是吸塵器來吹走灰塵。

 

4. When cleaning, clean and soft cloth should be used to wipe away the dust. For places where cloth is not easy to wipe in some ditches, brush or vacuum cleaner should be used to blow away the dust.

 

 

 

5、對于長時間經過擺放且出現暗啞現象的，擦試時不可大力用布擦，要用 棉質的細布輕輕擦試主要達到拋光的效果。

 

5. For those who have been placed for a long time and appear dumb phenomenon, the cloth should not be wiped vigorously during the wiping test. The cotton fine cloth should be wiped gently to achieve the polishing effect.